Coleman SaluSpa E02 Code: Causes and Safe Fixes
Coleman SaluSpa E02 means the pump system is not detecting water flow. Start by checking the fill level, the filter cartridge, the inlet and outlet openings, and any visible flow restrictions. E02 does not by itself mean that the heater or pump has failed.
Unplug the pump before touching the filter or other user-serviceable parts. Follow the manual for your exact SaluSpa pump, and contact Bestway if the code returns after these checks. There is no guaranteed repair time.
What Does the Coleman SaluSpa E02 Code Mean?
Bestway calls E02 a water-flow detection error. The system does not detect water flowing through its pump. The heater may stop as a consequence, but the error alone does not identify a faulty heating element.
The official Bestway hot tub FAQ directs owners to the filter cartridge, debris screens and the temporary stopper caps at the inlet and outlet. Check those simple causes before considering repairs.
Quick E02 Checklist
- Water sits within the MIN and MAX fill markings for your spa.
- The two temporary stopper caps are removed from the inlet and outlet openings.
- The accessible debris screens are clear of lint, leaves and visible limestone buildup.
- The correct filter cartridge is clean and the housing is properly assembled.
- External hoses are not visibly kinked or crushed.
- The correct model-specific reset has been followed after any blockage is corrected.

E02 quick diagnostic path — check each item in order; do not skip electrical safety steps.
- 1. Water levelBetween MIN and MAX marks
- 2. FilterClean, undamaged cartridge
- 3. Screens and capsClear screens; caps removed
- 4. Visible hosesNo kinks or crushed connections
- 5. ResetOnly as your pump manual directs
- 6. Still E02?Stop and contact Bestway support
Unplug power before handling the filter or inspecting user-serviceable parts. Do not remove safety guards, bypass the flow sensor or run a damaged pump.
Filter Cartridge, Debris Screen or Stopper Cap?
These three parts are often confused. The illustrations below are simplified symbols, not actual model-specific part photos. Compare your pump and liner with the labeled parts in Bestway’s official E02 guide and the manual supplied with your spa.
Removable pleated filter media inside its housing. Clean or replace it when restricted.
Mesh or slotted protection at the water opening. Inspect accessible screens; some are fixed in place.
Solid plugs used while the pump is disconnected. Remove them from water openings before operation.
How to Fix an E02 Error: Step-by-Step Checks
1. Check the water level
Confirm the water is within the marked fill range. Top it up if necessary. Do not operate a pump that cannot draw enough water through the spa.
2. Remove the stopper caps and check accessible screens
The caps used while attaching or detaching the pump must not cover the inlet and outlet during operation. Check accessible screens for debris or white calcium deposits. Bestway says the lower debris screen is not removable on some models; do not force it off.
3. Clean or replace a blocked filter cartridge
Disconnect electrical power before removing the cartridge. Look for heavy dirt, collapsed or damaged pleats, and buildup that restricts flow. Rinse or replace the cartridge according to the manual, using the correct filter type. Fixed replacement intervals do not apply to every owner.
Our inflatable hot tub filter cleaning guide explains routine cartridge care.

4. Use Bestway’s filter-isolation check if your model allows it
Bestway’s official E02 guide describes briefly activating filtration without the filter cartridge to help isolate a restriction. Only perform this check if the manual for your model permits it. If the error clears, inspect the cartridge and housing fit; reinstall the correct filter before normal use.
This is a supervised diagnostic check, not a way to operate without filtration. Follow the manual for your specific model, keep bathers out during the test, and do not put hands near an operating inlet.
5. Inspect visible hose restrictions
With the spa disconnected from electricity, look for kinked external hoses, crushed tubing or incorrectly seated connectors. Do not heat, cut or splice tubing; do not loosen pressurized joints; and never open the sealed electrical pump housing.
6. Follow the manufacturer’s reset procedure
The Bestway general FAQ says to unplug the pump, wait 30 seconds, plug it back in and reset the PRCD safety device. Restart filtration only after checking the possible cause. The procedure may differ across pump models, so use your owner’s manual if it says otherwise.
Resetting the alarm does not fix a water restriction. Never bypass a flow sensor, PRCD or any electrical protection.
7. Contact Bestway if E02 returns
If the error remains with proper water level, clear openings and a clean filter, turn off the spa and contact the manufacturer. Record the model number, when the error started and what you checked. Repeated errors may require professional diagnosis rather than a homeowner repair.
For other problems, our SaluSpa troubleshooting guide covers general checks. Only consider pump replacement costs if a qualified service provider has confirmed the pump needs replacement.
Unsafe E02 Fixes to Avoid
- Do not open the sealed pump housing, remove control panels or work on internal sensors.
- Do not bypass flow detection or the PRCD protection device.
- Do not cut hoses or use a heat gun and homemade clamps to change the plumbing.
- Do not assume the heater or control board has failed solely because E02 appears.
- Do not rely on a fixed 10-, 30- or 40-minute repair promise.
E02 After Refilling or in Cold Weather
After a refill: Confirm that temporary stopper caps are out, water is between the fill marks, the filter is properly seated, and visible hoses are not kinked. If you disconnected the pump, follow the manufacturer’s assembly and priming instructions before restarting. A recent refill is a useful clue, not proof that the pump has failed.
Cold-start check: Bestway notes that some Freeze Shield-equipped SaluSpa models may display E02 during setup when air or water is below about 42°F. Its official E02 instructions describe warming the spa and pump in an appropriate location at or above 50°F before setup. Follow the specific directions for your model, not a universal temperature rule. If water or components may be frozen, do not force the pump to run; contact Bestway.
How to Prevent Repeat E02 Errors
- Keep water between the fill markings and maintain proper sanitation.
- Check the cartridge regularly, especially after heavy use.
- Remove debris from accessible water openings during routine maintenance.
- Fit only manufacturer-compatible filter cartridges.
- After setup or draining, confirm stopper-cap removal and hose routing before powering on.
For a broader maintenance routine, see how to maintain an inflatable hot tub. Good upkeep helps avoid flow restrictions, though it cannot prevent every equipment fault.
Is E02 the Same as E01 or E03?
No. Bestway describes E01 as a water-flow sensor-position or sensor fault, E02 as undetected circulation, and E03 as water temperature below 39°F. Follow the manual for the code actually displayed.
Frequently Asked Questions
What does E02 mean on a Coleman SaluSpa?
E02 means the system is not detecting water flow through the pump. Check the water level, filter cartridge and accessible inlet or outlet openings.
Can a dirty filter cause E02?
Yes. Bestway identifies restricted filter cartridges as a common possible cause and describes a filter-isolation check to help confirm this.
Can I reset E02 without replacing the pump?
Sometimes. Correct any visible water-flow problem first, then follow the model’s reset instructions. Bestway’s general FAQ describes a 30-second unplug interval and a PRCD reset.
Should I bypass the water-flow sensor?
No. A sensor or safety-device bypass is not an appropriate homeowner fix. Seek manufacturer assistance if the code persists.
What if the code returns after cleaning the filter?
Recheck the water level, stopper caps, screens and visible flow restrictions. If E02 still returns, stop using the spa and contact Bestway.
The Safe Next Step
An E02 warning calls for water-flow checks, not pump disassembly. Work through the water level, filter, intake and outlet checks first. When those do not help, the safest next step is model-specific support rather than improvising an electrical or plumbing repair.









Any thoughts on this. My Coleman Saluspa was working perfectly in the middle of CT winter. Cold. below freezing, worked like a champ. The power went out and the pump went off. It was off for about 24 hours when I noticed and the temperature on the unit says 66F. So I start it up and it says E02. The filter is clean but the E02 error keeps coming on. Middle of a winter storm with low temps. Is it because the air is to cold so it wont start? Will the freeze shield still work or will it be shut down by the E02. Not looking good. Thoughts?
Dear sean,
The E02 error code on your Coleman Saluspa typically indicates a problem with water flow. This could stem from issues like blocked filters, low water level, or potentially, due to CT winter temperatures, water freezing in the tub. Here’s how to troubleshoot:
1. Make sure your spa is adequately filled with water.
2. Check and clean the filter cartridges or replace if necessary.
3. If weather permits, ensure that the temperature of the spa does not drop too low as to freeze the water.
Remember, always switch off and unplug your Saluspa before any maintenance checks for safety reasons. If above advice doesn’t resolve your issue, it may be time to contact Coleman customer service for further assistance.
Stay warm,
Hot Tub Patio